The free Annulus Area Calculator lets you enter the outer radius R and inner radius r to calculate π(R² − r²) instantly.

An annulus is the flat, complete ring between two concentric circles, meaning the circles share the same center. Familiar examples include a washer, a CD, a doughnut viewed from above, and the cross-section of a pipe wall. To find its area, subtract the smaller circle from the larger one.

annulus area calculator free no sign up
Annulus Area Calculator: Free

What the annulus area formula represents

The full outer circle has an area of πR², while the inner circle has an area of πr². Removing the inner disk gives:

Annulus area = πR² − πr² = π(R² − r²)

Both measurements are radii, so each runs from the common center to its circle’s edge. The calculator also displays the ring width, which is R − r, along with the two individual circle areas. That gives you a compact way to check both the shape and the subtraction behind the final result.

  • Annulus area: the area of the complete ring.
  • Outer circle area: πR² for the full disk bounded by the outer radius.
  • Inner circle area: πr² for the disk removed from the center.
  • Ring width: R − r, the radial distance across the ring.

Calculate the ring area in three steps

The tool takes only the two radii and does the calculation for you.

  1. Enter the outer radius. Type R into the first box. You can choose any unit, but use that same unit for the inner radius.
  2. Enter the inner radius. Type r into the second box. The inner radius must be smaller than R.
  3. Read the result. The annulus area appears below the inputs. The same result area also shows the outer circle area, inner circle area, and ring width.

This workflow avoids unnecessary conversions or intermediate arithmetic. Once both valid radii are present, the browser displays the area and its supporting values directly.

Keep both radii in the same unit

The calculator is unit-agnostic: it does not convert one measurement into another. Instead, it squares whichever length unit you enter. Use centimeters for both radii and the area is reported in square centimeters; use meters and it is reported in square meters.

Unit for both radiiAnnulus and circle areasRing width
CentimetersSquare centimetersCentimeters
MetersSquare metersMeters
InchesSquare inchesInches

Keep the two radii in one consistent unit before entering them. Mixing values such as centimeters and inches would make the subtraction mathematically unreliable. Convert both measurements first, then enter the converted outer and inner radii together. The calculator preserves the chosen convention rather than changing units behind the displayed result.

Check the radius limits before reading the result

For a valid annulus, the inner circle must fit inside the outer circle. The calculator accepts zero and positive radii, while negative distances are rejected because a radius cannot be negative.

Input conditionGeometric meaningCalculator behavior
0 ≤ r < RA positive-width ring, including a central hole with zero radiusAccepts the inputs and calculates the area
r = RThe ring has collapsed to zero widthBlocks the input with a clear message
r > RThe inner circle would be larger than the outer circleShows a clear invalid-input message instead of returning a negative area
Either radius is negativeA negative length cannot represent a radiusRejects the negative value

The r > R case is not a reversed ring with a meaningful negative area; it is an impossible arrangement. Likewise, a negative radius is not a direction to preserve. Correcting these values ensures the displayed result represents a real geometric shape.

Worked example: outer radius 10 and inner radius 6

Formula: A = π(R² − r²)

Substitute the radii: A = π(10² − 6²)

Simplify: A = π(100 − 36) = 64π

Result: A = 64π ≈ 201.06 square units.

For this same ring, the outer circle area is 100π, or approximately 314.16 square units, and the inner circle area is 36π, or approximately 113.10 square units. The ring width is 10 − 6 = 4 units. These are the companion values shown by the calculator.

Use the companion outputs as checks

The extra outputs make it easier to catch a mislabeled radius or a unit mismatch before using the answer.

  • Check the subtraction: outer circle area minus inner circle area should equal the annulus area.
  • Check the width: R − r should match the displayed ring width.
  • Check the dimensions: area belongs in square units, while width remains a length in the original unit.
  • Check the radius roles: the larger value belongs in the outer-radius box and the smaller value in the inner-radius box.

A result can look numerically plausible while still representing the wrong shape, so these checks are more useful than judging by size alone. The formula is simple; consistent inputs and correct radius labels are what make it reliable.

Where annulus area calculations are useful

A complete ring area appears in engineering, fabrication, landscaping, and geometry. The calculator is useful when you already know the inner and outer radii and need the flat area between them.

  • Hollow shafts, tubes, and pipes: the ring area represents part of the material’s cross-section.
  • Washers, flanges, and gaskets: subtracting the center opening gives the material’s flat footprint.
  • Circular paths, pond rims, and track lanes: a band between two radii can be treated as an annulus.
  • Ring-shaped stock: machinists and metalworkers can compare the area of the usable ring.
  • Geometry and calculus: the same subtraction supports lessons on circles, areas between curves, and integration.

In an engineering or design task, this result is one component rather than a complete specification. Material weight, cost, structural capacity, and other design requirements need their own calculations and applicable standards.

Full annulus or annulus sector?

An annulus is the entire 360° ring. An annulus sector is only a slice of that ring, bounded by two radii and an angle. For a sector, the full-ring area must be multiplied by the fraction of the circle it occupies.

In degrees, the sector area is (θ/360) × π(R² − r²); in radians, it is (θ/2) × (R² − r²). This calculator computes the full annulus only, so its result should not be used as the area of a partial sector without applying the appropriate angle fraction.

Avoid common radius and unit mistakes

  • Do not enter a diameter as a radius. A radius is half the diameter, so convert the measurement first when only the diameter is known.
  • Do not mix units. Both radii must use the same length unit before they are squared and subtracted.
  • Do not reverse R and r. The outer radius must be larger than the inner radius.
  • Do not treat ring width as area. R − r is measured in units such as centimeters, while π(R² − r²) is measured in square centimeters.
  • Do not use a full-ring result for a sector. A partial ring requires an additional angular fraction.

Free calculator with local processing

The calculator is free to use. Everything runs locally in your browser, and the entered values are not uploaded.

That setup keeps the workflow focused on the geometry: choose a unit, enter the outer and inner radii, and read the annulus area with the outer area, inner area, and width beneath it.

If you're weighing options, Area Converter Accurate? Exact Factors for 9 Units covers this in detail.

If you're weighing options, Cylinder Surface Area Calculator: Accurate Formula Checks covers this in detail.