For a regular hexagon, the area from a center-to-vertex radius is A = (3√3/2)r² because the circumradius r equals the side length.
That answer assumes “radius” means the distance from the center of a regular hexagon to one of its corners. A hexagon also has an apothem, which is the distance from the center to the midpoint of a side. These measurements are not interchangeable, so identifying the radius on a diagram is the first step.

Distinguish the two hexagon radii
A regular hexagon can be related to two different circles. The circle passing through all six vertices has the circumradius, while the largest circle contained inside the hexagon has the apothem, also called the inradius.
| Radius type | Where it is measured | Relationship to side length | Area approach |
|---|---|---|---|
| Circumradius, R | From the center to any corner | R = s for a regular hexagon | A = (3√3/2)R² |
| Apothem, a | From the center to the midpoint of a side | a = (√3/2)s | Convert to s = 2a/√3, or use A = 2√3a² |
For example, a hexagon drawn inside a circle normally uses the circle’s radius as the hexagon’s circumradius. A hexagon drawn around a circle uses the circle’s radius as the hexagon’s apothem. In both cases, the method below gives the correct area for a regular hexagon.
Area from a center-to-vertex radius
When a regular hexagon is inscribed in a circle, connect its center to all six vertices. This divides the hexagon into six congruent triangles. Each has a central angle of 60 degrees, so every triangle is equilateral with side length equal to the radius.
The area of one equilateral triangle with side s is (√3/4)s². Adding the six identical triangles gives:
A = 6 × (√3/4)s² = (3√3/2)s²
Because s = R for a regular hexagon, the radius form is:
A = (3√3/2)R²
As a single worked example, suppose the distance from the center to each vertex is 2 units. The side length is also 2 units, so:
A = (3√3/2) × 2² = (3√3/2) × 4 = 6√3 ≈ 10.3923 square units
The same measurement gives a perimeter of 12 units, an apothem of √3 ≈ 1.7320508 units, and a circumradius of 2 units.
Area when the radius reaches a side
If the given radius extends from the center to the midpoint of one side, treat it as the apothem rather than the circumradius. In that case, the side length is not equal to the radius.
The apothem and side length are related by a = (√3/2)s. Rearranging gives the side length needed by the standard area formula:
s = 2a/√3
You can also substitute that relationship directly into the area formula:
A = (3√3/2)(2a/√3)² = 2√3a²
Either route gives the same result. To use the calculator, calculate s = 2a/√3 first and enter that value as the side length. A longer explanation of this relationship is available in the guide to calculate regular hexagon area from its apothem.
Do not enter an apothem directly as though it were a side or circumradius. That would produce a different, incorrect area. The distinction is essential when reading a diagram whose radius line ends at a side rather than a vertex.
Calculate the result in the Hexagon Area Calculator
The Hexagon Area Calculator accepts a side length as its length input. It does not have separate fields for circumradius or apothem, so use the relationships above before entering a value.
- Identify the radius type. If the measurement runs from the center to a vertex, it is the circumradius. For a regular hexagon, enter that value directly as the side length because R = s.
- Convert an apothem when necessary. If the measurement runs from the center to the midpoint of a side, calculate s = 2a/√3. Do not enter the apothem unchanged.
- Enter the side length in one consistent unit. Open the Hexagon Area Calculator, type the value into the side-length field, and the calculator applies A = (3√3/2)s² and displays the worked formula.
- Read the area in square units. If the side was entered in centimeters, the result is square centimeters; meters produce square meters, and inches produce square inches.
- Check the supporting measurements. The displayed perimeter, apothem, and circumradius can help confirm that the side length was entered and interpreted correctly.
Outputs that verify the hexagon
Besides the area, the calculator returns three related dimensions. Each has a direct connection to the entered side length:
- Perimeter: P = 6s, since a regular hexagon has six equal edges.
- Apothem: a = (√3/2)s, the distance from the center to a side and the radius of the inscribed circle.
- Circumradius: R = s, the distance from the center to a vertex and the radius of the circle through all six corners.
These outputs are more than extra figures. They let you verify that a center-to-vertex radius was handled as expected: after entering the side length, the circumradius should match that side length exactly. If you began with an apothem and converted it to a side length, the calculated apothem should agree with your original measurement.
For physical parts and layouts, the distinction also determines which dimension to compare with a drawing or measurement. Hex nuts, for example, are commonly identified by the width across their flats, which is twice the apothem. The center-to-vertex distance is instead the circumradius.
Units, precision, and conversion limits
The side-length field is unit-agnostic, but the calculator does not convert units. Enter the measurement in one unit and interpret the area as that unit squared. If a drawing provides millimeters and another part of the calculation uses inches, convert the values before entering them rather than mixing the two systems.
The calculation uses the exact value of √3 rather than a rounded value such as 1.732. That keeps the displayed area accurate to many decimal places and avoids introducing an unnecessary approximation into the formula.
All processing takes place locally in your browser, and the side-length measurement is not uploaded. The calculator updates the results as the value is entered, so there is no need to round the side length before using it.
When the radius method applies
This method depends on the hexagon being regular: all six sides and all six interior angles are equal. A radius alone does not determine the area of an irregular hexagon, because its vertices may not be evenly spaced around the center. For that case, use information specific to the shape rather than applying the regular-hexagon formula.
The radius relationship is especially useful when a regular hexagon is specified by its circumscribed circle, a tile pattern is based on a repeating regular hexagon, or a technical drawing labels a center-to-vertex dimension. It also provides a direct method for geometry exercises involving hexagons, machining profiles, quilting, and other designs built from regular six-sided units.
The key rule is simple: a center-to-vertex radius can be used as the side length, while a center-to-side radius must first be converted. Once the correct side length is established, the Hexagon Area Calculator provides the area and the related dimensions without changing the unit you entered.
If you're weighing options, How to Calculate Ideal Weight in kg: Formulas and Checks covers this in detail.