A frequency converter chart expresses one frequency in equivalent units, with 1 kHz = 1,000 Hz and each larger SI prefix adding a factor of 1,000.

The chart gives a quick reference across Hz, kHz, MHz, GHz, THz, mHz, rpm, BPM, rad/s, and deg/s. For a live calculation, the Frequency Converter converts any selected pair in your browser, and the entered values stay on your device.

frequency converter chart
Frequency Converter Chart: Units, Formulas, and Steps

Frequency units at a glance

Hertz (Hz) counts complete cycles per second. The SI-prefixed frequency units use powers of ten, while rpm and BPM count events per minute and rad/s and deg/s describe angular motion.

Unit Exact relationship What it measures
mHz 1 mHz = 1/1,000 Hz One thousandth of a hertz
Hz 1 Hz = 1 cycle/s Complete cycles per second
kHz 1 kHz = 1,000 Hz One thousand hertz
MHz 1 MHz = 1,000,000 Hz One million hertz
GHz 1 GHz = 1,000,000,000 Hz One billion hertz
THz 1 THz = 1,000,000,000,000 Hz One trillion hertz
rpm 1 rpm = 1/60 Hz Revolutions per minute
BPM 1 BPM = 1/60 Hz Beats per minute
rad/s 1 rad/s = 1/(2π) Hz Angular frequency in radians per second
deg/s 1 deg/s = 1/360 Hz Angular frequency in degrees per second

Read each row as an exact unit definition, not a rounded ranking. The converter routes every pair through hertz, so the same frequency can be compared without shifting between reference systems. rpm and BPM remain separate labels even though their rate relationship is identical.

Convert a frequency with the Frequency Converter

  1. Type the frequency you want to convert into the frequency value field.
  2. Choose the source unit under From and the target unit under To. The available choices are Hz, kHz, MHz, GHz, THz, mHz, rpm, BPM, rad/s, and deg/s.
  3. Read the converted result as soon as the source and target are selected.
  4. For a side-by-side reference, tick Show all units at once to see every unit from millihertz to terahertz together, alongside rpm, BPM, rad/s, and deg/s.

The order of the two unit menus controls the direction of the conversion. When copying a figure from a datasheet or instrument panel, transcribe both the number and its unit first; this prevents a value such as a radio-band frequency from being mistaken for an audio or mechanical rate.

How the SI scale works

Following the BIPM definitions, kilo is 10³, mega is 10⁶, giga is 10⁹, tera is 10¹², and milli is 10⁻³. Moving from hertz to kilohertz, megahertz, gigahertz, or terahertz divides the displayed number by 1,000 at each step. Moving back toward hertz multiplies it by 1,000.

For a two-step conversion, first express the input in hertz and then divide by the target unit’s factor:

Hz value = input × source-to-Hz factor

Target value = Hz value ÷ target-to-Hz factor

A single example shows the decimal shift. Suppose a label gives 2.5 kHz and the required unit is hertz:

Formula: Hz = kHz × 1,000

Substitution: 2.5 × 1,000

Result: 2,500 Hz

The decimal shortcut applies to the SI-prefixed frequency ladder only. It does not replace the per-minute factors for rpm and BPM or the angular factors for rad/s and deg/s.

Rate and angular units use different factors

Revolutions per minute and beats per minute are both measured over a minute. To convert either rate to ordinary frequency in hertz, divide the rate by 60. To convert hertz back to a per-minute rate, multiply by 60. The arithmetic is the same, but the label carries a different meaning: rpm describes rotations, while BPM describes beats in music or heart-rate contexts.

Angular frequency uses radians rather than whole cycles. Its relationship to ordinary frequency is ω = 2πf. Therefore, convert rad/s to Hz by dividing by 2π, and convert Hz to rad/s by multiplying by 2π. A value written in rad/s is not numerically interchangeable with the same number in Hz because one full cycle sweeps 2π radians.

Degrees per second uses a full turn of 360 degrees. Divide deg/s by 360 to obtain hertz, or multiply hertz by 360 to obtain deg/s. The converter uses 2π exactly rather than a rounded value, so moving from hertz to rad/s and back returns the original number.

Choose units by application

Different fields use frequency units for different reasons. Use this comparison to choose the unit printed on the source document, then let the converter apply the proper factor and provide the exact converted figure.

Application Common units Reading note
Radio and wireless kHz, MHz, GHz These units use the SI prefix ladder.
Audio and music Hz, BPM Hz counts cycles, while BPM counts beats per minute.
Processors and signal timing MHz, GHz Choose the prefix used by the component or signal documentation.
Rotating machinery rpm Keep the mechanical-revolution label when transferring the result.
Angular motion rad/s, deg/s Use the angular-frequency factor rather than an SI-prefix rule.
Light and spectroscopy THz THz represents the high-frequency end of the SI ladder.

For a particular measurement, keep the source unit visible in your notes and record the target unit with the result. If several equivalent units could fit the task, choose the one already used by the relevant datasheet, standard, or instrument rather than changing the label unnecessarily.

Checks that catch unit mistakes

  • Check the direction: as the SI prefix rises from Hz to THz, the numeric value for the same frequency falls. Moving down the ladder multiplies the number by 1,000.
  • Keep rate labels distinct: rpm and BPM share a conversion factor, but they describe different events. A tempo should not be relabeled as a motor speed.
  • Check angular units: use 2π for rad/s and 360 for deg/s; neither is an SI-prefixed hertz unit.
  • Check the inverse: swap From and To, then enter the converted result. The output should return to the starting figure because all supported conversions use exact relationships through hertz.
  • Compare the full scale when useful: the all-units view makes the relative size of mHz, Hz, kHz, MHz, GHz, and THz easier to spot while keeping the rate and angular units visible.

Scope and limits of the converter

The documented function is numerical unit conversion. It does not modify an emitted signal, choose a waveform, or control a motor; a hardware frequency converter or variable-frequency drive is a different application. The chart also should not be used as though every unit measures the same physical quantity: hertz counts cycles, BPM counts beats, rpm counts revolutions, and angular units count rotation around a circle.

If the larger task is wavelength rather than a unit conversion, you also need the propagation-speed relationship v = f × λ; the guide to converting frequency to velocity with v = f × λ shows that method. For photon energy, the separate relation E = h × f applies; see how to calculate frequency-related energy. Neither wavelength nor energy is an output promised by the frequency converter.

All frequency and rate conversions run client-side, so the values never leave your device. For a quick lookup, use the chart; for a specific pair of units, enter the original value unchanged and let the converter perform the unit conversion.