The lateral, or slant, surface area of a right circular cone is πrl, while the total surface area is πr(r + l), where l = √(r² + h²).
A cone slant surface area chart brings these formulas together in one reference. It helps you distinguish the curved side from the circular base, identify the measurement you still need, and select the correct result for an open or closed cone.

Cone Slant Surface Area Chart
Use this chart to keep the four related cone measurements separate. The formulas below apply to a right circular cone, whose apex is directly above the center of its circular base.
| Quantity | Formula | Values needed | What it covers |
|---|---|---|---|
| Slant height | l = √(r² + h²) | Radius r and vertical height h | Straight distance along the cone’s side from the base edge to the apex |
| Base area | Abase = πr² | Radius r | The flat circular base |
| Lateral or slant surface area | Alateral = πrl | Radius r and slant height l | The curved side only |
| Total surface area | Atotal = πr² + πrl = πr(r + l) | Radius r and slant height l | The curved side plus the circular base |
The radius, vertical height, and slant height form a right triangle. The vertical height h runs from the base plane to the apex, while the slant height l follows the cone’s sloping side. This is why h cannot be inserted directly into the lateral-area formula in place of l.
If a worksheet already provides the slant height, skip the square-root step and use l in πrl or πr(r + l). A direct method for finding cone surface area from a known slant height shows how to use that information without calculating the height.
Here, “chart” means a formula-and-application reference rather than a precomputed grid covering every radius and height. Exact numerical values depend on the dimensions of the cone you enter into the calculator.
Calculate a Cone from Radius and Height
- Measure the base radius r. Measure from the center of the circular base to its edge. If you have the diameter instead, divide it by two before entering the radius.
- Measure the vertical height h. This is the perpendicular distance from the center of the base to the apex, not the distance measured along the sloping side.
- Enter the two measurements in order. Open the Cone Surface Area Calculator, enter the base radius in the first field, and enter the vertical height in the second field. The calculator derives the slant height automatically.
- Read the four related outputs. The display gives the total surface area, slant height, lateral area, and base area, so you can see how the final result is formed.
- Choose the area required by the task. Use lateral area for an open cone or another measurement that excludes the bottom. Use total area when both the curved side and circular base must be counted.
The calculator’s supported workflow starts with the radius and vertical height rather than a separate slant-height field. You therefore do not need to rearrange the formula yourself when your available measurement is h. All calculations run entirely in your browser, so nothing you type is uploaded.
Choose Total or Lateral Surface Area
The most important row to interpret in the chart is the one describing whether the base is included. A cone may have a bottom, as a solid model does, or it may be an open wrapper with only a curved side.
| Situation | Area to use | Reason |
|---|---|---|
| Closed cone with a circular bottom | Total surface area | Includes both the curved side and the base |
| Open cone with no bottom | Lateral surface area | Counts the curved side but excludes the base |
| Paper, fabric, or sheet wrapping for a cone | Lateral surface area | Represents the wrapper-like curved surface |
| Every exterior face of a solid cone | Total surface area | Adds the flat base to the curved surface |
The total area is always the lateral area plus the base area, so it is larger by πr² for every cone with a positive radius. The chart also helps prevent a common mismatch: a question about the “wrapper” or curved side usually calls for lateral area, while a question about the outside of a complete cone calls for total area.
These results represent ideal geometric surface areas. An allowance for seams, overlap, fastening, or waste must be considered separately when the number is being used to purchase or cut material.
Worked Example: Radius 3 cm, Height 4 cm
For a cone with a base radius of 3 cm and a vertical height of 4 cm, start by finding the slant height:
l = √(r² + h²) = √(3² + 4²) = √25 = 5 cm.
The flat base area is:
Abase = πr² = π(3²) = 9π ≈ 28.27 cm².
The lateral, or slant, surface area is:
Alateral = πrl = π(3)(5) = 15π ≈ 47.12 cm².
Adding the base and curved side gives the total surface area:
Atotal = 9π + 15π = 24π ≈ 75.40 cm².
For this cone, use 47.12 cm² if the bottom is open and 75.40 cm² if the circular base is included. Because both linear measurements were in centimetres, the area results are in square centimetres.
How the Area Chart Works
The curved side of a cone can be unrolled into a circular sector. That sector has radius l and an arc equal to the base circumference, 2πr. Its area is one-half of radius times arc length, so ½ × l × 2πr = πrl. This gives the lateral area shown in the chart. Adding the circular base, πr², produces the total area.
- Radius r: the horizontal distance from the base center to the rim.
- Vertical height h: the perpendicular distance from the base center to the apex.
- Slant height l: the straight-line distance along the sloping side from the rim to the apex.
- Lateral area: the curved surface without the base.
- Total area: the curved surface plus the base.
For a non-degenerate right circular cone, the slant height is longer than the vertical height because it must cover both the rise and part of the radius across the right triangle.
Units and Measurement Checks
Check these details before relying on a chart result or calculator output:
- Keep both inputs in the same unit. If r and h are in centimetres, the areas are in cm². If they are in inches, the areas are in in².
- Enter the radius, not the diameter. Convert a diameter to a radius by dividing it by two.
- Use vertical height for h. A side measurement is the slant height, not the height used in l = √(r² + h²).
- Confirm that the cone is right circular. These formulas assume the apex is directly above the center of the circular base.
- Match the output to the surface required. Do not use total area for an open cone unless its separate base must also be included.
Surface area is always expressed in square units because it measures a two-dimensional area. The numerical relationship stays the same across compatible units, but the unit label changes with the linear measurement used.
Where Cone Area Charts Help
For geometry homework, the chart provides a quick way to separate the cone’s curved surface from its base and match each quantity to its formula. It is also useful when checking whether a problem supplies a slant height, radius, and vertical height, or only the two dimensions needed to derive another value.
For model-making and fabrication, the lateral area gives the curved portion needed for a paper, fabric, or sheet-metal cone. The total area adds the circular bottom when one is present. These are geometric measurements, so practical material planning may require additional allowance beyond the displayed area.
Coating or covering questions follow the same distinction. A task involving the entire outside of a conical roof or hopper may call for total area, while a wrapper, party hat, ice-cream cone, or funnel without a bottom calls for lateral area. The chart helps make that selection before you enter the dimensions.
For a deeper look, see Cone Volume Calculator Alternative: Manual vs. Online.