A Brinell hardness calculator chart converts an applied load F, ball diameter D, and measured indentation diameter d into a Brinell hardness number (BHN/HBW).
The Brinell Hardness Calculator uses the ASTM E10 equation and updates the result as the measurements are entered. It is a focused Brinell calculation tool, not a universal Rockwell-to-Vickers conversion chart: its documented inputs are F, D, and d.

Calculator inputs at a glance
A useful Brinell input chart separates the measurements taken during the test from the units used to report them. Each value has one specific role in the calculation.
| Input | Meaning | Accepted format | Key requirement |
|---|---|---|---|
| F | Applied test force | kgf or N | Select the matching load unit before calculation |
| D | Diameter of the indenter ball | Millimetres | Common sizes are 10, 5, 2.5, and 1 mm |
| d | Diameter of the residual indentation | Millimetres | Must be greater than zero and smaller than D |
Measure the indentation rather than estimating it from the material grade. The residual indent is usually measured with a microscope, often as the mean of two readings taken perpendicular to each other. The ball diameter must describe the same indenter used in the physical test, and the load must correspond to the force recorded for that test.
How the ASTM E10 formula is applied
The calculator applies the Brinell hardness equation:
BHN = 2F ÷ [πD(D − √(D² − d²))]
In the classic form of the formula, F is the applied force in kilogram-force, while D and d are both measured in millimetres. If the test record uses newtons, select N in the calculator. The tool then divides the entered force by 9.80665, because 1 kgf equals 9.80665 N, before applying the formula.
Conceptually, Brinell hardness is the applied load divided by the curved surface area of the spherical impression. A harder material resists the ball and leaves a smaller indentation; a softer material allows a wider indentation. The result is normally written as BHN. Modern reports use HBW when a tungsten-carbide indenter was used, while older results from hardened-steel balls may carry HBS or simply HB.
Enter the three test values
Open the Brinell Hardness Calculator and use the measurements from the same Brinell test.
- Choose the load unit and enter F. Select kgf if the test force was recorded in kilogram-force. Select N for newtons, then enter the numerical force exactly as recorded.
- Enter the ball diameter D in millimetres. Use the actual diameter of the indenter, commonly 10, 5, 2.5, or 1 mm. Do not substitute the specimen thickness or another test dimension.
- Enter the measured indentation diameter d in millimetres. Read the BHN/HBW result as soon as the value is entered. A zero, negative, or non-smaller-than-D indentation is rejected because it cannot describe a valid Brinell impression.
The calculation runs in your browser and requires no sign-up. It is designed for converting existing test measurements, checking a manual calculation, or exploring how a proposed load and ball size would affect the calculated reading before a physical test.
Worked example: 750 kgf, 5 mm ball, 2 mm indent
Consider an illustrative test with F = 750 kgf, D = 5 mm, and d = 2 mm. Substituting those measurements gives:
BHN = 2(750) ÷ [π × 5 × (5 − √(5² − 2²))]= 1500 ÷ [π × 5 × (5 − √21)]= 1500 ÷ 6.556886≈ 228.8
The calculated value is approximately 228.8 BHN. It should be identified as HBW only if the test used a tungsten-carbide indenter; the diameter and load alone do not establish the indenter material.
Load and hardness reference chart
Load choice determines how the Brinell indentation forms and whether readings can be compared with other tests. For load planning, use F in newtons with the 0.102F/D² comparison expression; the calculator’s N setting converts the force to the kgf form used in the hardness equation.
| Material class | Reference factor for 0.102F/D² | Rough Brinell range |
|---|---|---|
| Steel and cast iron | 30 | About 120–250 HBW for mild and medium-carbon steels; about 400–650 HBW for hardened tool steels and bearing races |
| Copper alloys | 10 | Around 30–90 HBW for pure copper |
| Soft metals such as aluminium | 2.5–5 | Around 30–90 HBW for pure aluminium |
These are broad reference ranges, not material acceptance limits. Soft lead and tin can be around 20 HBW. The appropriate standard, grade, and product specification should determine the required load and permissible result for a particular inspection.
Measure the indentation correctly
During a Brinell test, a hardened or tungsten-carbide ball of diameter D is pressed into the metal under a fixed load F. The load is commonly held for a dwell time of 10 to 15 seconds so the material can deform. After the force is removed, the test leaves a round impression that must be measured with a microscope.
Accuracy depends on using the mean of the two perpendicular indentation readings where specified, then entering that mean as d. The diameter must also represent the actual residual indent rather than the curved depth below the original surface.
The physical constraint is strict: d must be smaller than D. If d were equal to or greater than the ball diameter, the impression would be impossible and the square-root term would be undefined. The calculator rejects those values along with zero or negative indentation entries.
What this calculator can and cannot do
Because the documented workflow contains only F, D, and d, the tool cannot directly accept an HRC, HRB, Vickers, or other hardness reading. It also does not measure the indent, operate the testing machine, select a certified laboratory load, or replace the physical Brinell procedure. Its result is a calculation from supplied test data.
That distinction matters when searching for a “hardness chart.” A Brinell calculator chart organizes inputs, units, load references, and valid ranges; it is not a general conversion chart. If the starting value is already Rockwell or Vickers, an approximate steel hardness conversion chart may help with scale comparisons, but the result should remain identified as an approximation rather than a newly measured Brinell value.
Choose the right hardness method
Brinell testing is well suited to castings, forgings, coarse-grained metals, and non-homogeneous materials because its comparatively large indentation averages out local surface variation. It is used with steel, cast iron, aluminium, copper alloys, and bearing metals for incoming inspection, heat-treatment verification, and quality control.
Rockwell testing measures indentation depth for a fast dial reading, while Vickers testing uses a diamond pyramid and is suited to very hard or thin materials. These systems use different scales and are not directly interchangeable without conversion tables.
For Brinell work, keeping the load-to-diameter relationship consistent within a material class improves comparability. The calculator can also demonstrate the direction of change when different loads or ball sizes are entered, but a meaningful physical reading still depends on using a valid test procedure and measuring the resulting indent accurately.
Final checks before using a result
Before accepting a calculated Brinell value, confirm the following:
- The force unit matches the test report and all three values come from the same test.
- D is the actual ball diameter, stated in millimetres.
- d is the measured residual indentation, not the penetration depth.
- The indentation satisfies 0 < d < D.
- The load and ball size follow the applicable material-class guidance.
- The result is labelled HBS, HB, or HBW consistently with the indenter used.
Recording F, D, d, and the resulting hardness makes the calculation reproducible and helps distinguish a calculation error from a measurement or test-procedure issue.
Related reading: Accurate Circle Area Calculator: Formula and Checks.
Related reading: Circumference Calculator Chart: Formulas and Steps.