The 50 MiB limit in Audio Effects Online is the maximum encoded size of the single input file selected for a run. It is an input-size gate, not an export cap: the processed WAV can have a different byte size, subject to its own decoded-output budget.
That distinction answers the practical question behind the limit. A file can be small enough to select yet fail later because its codec is not decodable in the current browser and operating system, because the decoded channel-sample count is too high, or because an effect tail pushes the complete output beyond the output budget. The 50 MiB number therefore does not guarantee that a run will finish.

What the 50 MiB limit measures
The limit applies to one encoded source file before it is decoded or processed. MiB means binary megabytes, so the exact ceiling is 50 MiB = 50 × 1,048,576 = 52,428,800 bytes. The size check itself does not directly cap duration, sample rate, channel count, or final WAV size.
Because all file reading, decoding, sample processing, WAV encoding, and download creation happen in the current browser tab, this is not a bandwidth allowance, upload quota, or account-storage rule. The audio is not uploaded to Lizely or stored in an account.
| Check | What it covers | Practical requirement |
|---|---|---|
| Encoded input size | The one selected source file | No larger than 50 MiB |
| Browser decoding | Codec and profile support in the current browser and operating system | A recognized extension alone does not guarantee a successful decode |
| Decoded input | 1–8 equal-length channels, an 8,000–192,000 Hz sample rate, and no more than 30 million channel samples | A file below the size ceiling can still exceed the decoded-input budget |
| Complete output | All processed frames, including any calculated echo or reverb tail | No more than 30 million channel samples; an oversized result is not truncated |
| Effect control | One selected effect and its whole-number amount | Choose one effect and set an amount from 0% through 100% |
The decoded-input and complete-output budgets are separate checks. A source that passes the encoded-size check can still contain too many channel samples after decoding. Echo and reverb make this distinction especially important because they add frames to the result. If the complete output would exceed 30 million channel samples, the tool creates no file rather than cutting off the calculated tail.
Why a sub-50 MiB file can still fail
File size and decodability are different requirements. Audio Effects Online recognizes filenames ending in MP3, WAV, M4A, AAC, Ogg, WebM, or FLAC, but actual codec and profile support varies by browser and operating system. Changing a file's extension does not make an unsupported encoding decodable. If decoding fails, the tool creates no result.
Compression can also conceal a large decoded recording. A long, highly compressed source may occupy less than 50 MiB on disk but expand beyond the tool's channel-sample budget when the browser decodes it. The decoded input must meet the channel, sample-rate, and channel-sample requirements in the table above.
Effect selection has its own independent rules. One run applies one effect with a whole-number amount from 0% through 100%. At full amount, echo retains each input sample and adds a half-strength copy 200 milliseconds later; lower amounts scale that delayed copy. The lightweight reverb uses three disclosed reflections at 29.7, 37.1, and 41.1 milliseconds. Both allocate their complete tails before processing, so the calculated ending is retained when the output fits the budget.
Apply one effect within the limits
- Open Audio Effects Online, keep an untouched copy of your source, and select one browser-decodable audio file no larger than 50 MiB. Confirm the actual encoded size rather than relying on a rounded label.
- Select exactly one effect: echo, lightweight reverb, reverse, fade in, fade out, or normalization. Set a whole-number amount from 0% through 100%, then confirm that this is the file, effect, and amount you want to process.
- Apply the effect locally in the current browser tab. The browser performs the decoding and processing. If decoding fails, no result is produced, so use a source whose codec and profile the current browser and operating system can decode.
- Inspect the reported channel count, sample rate, input and output frame counts, output peak, and exact WAV byte size. For echo or reverb, a larger output frame count reflects the added tail. If the complete output exceeds 30 million channel samples, no file is created and the tail is not truncated.
- Download the completed PCM16 WAV and retain the untouched original. To build a chain, download one result and use that WAV as the input to a later run; each run still applies one effect and must pass the input, decode, and output checks. Repeated processing can reveal source artifacts or change dynamics.
Why the downloaded WAV can have a different size
The 50 MiB limit applies only to the encoded source. The export is a new interleaved, little-endian PCM16 RIFF/WAVE file, and its size follows the processed sample data, sample rate, channel structure, and any added effect tail. Echo and reverb can extend the timeline, while the source's original compressed representation may be much smaller than its decoded PCM data. There is no rule requiring the downloaded WAV to remain below 50 MiB, and the page reports its exact byte size after processing.
The W3C Web Audio API 1.1 defines AudioBuffer length in sample frames, which is why the displayed frame counts describe decoded audio rather than compressed file packets. Microsoft’s WAVEFORMATEX structure reference documents PCM block alignment, which determines how channel samples are arranged within the WAV data.
The export preserves the processed channel samples and sample rate. It does not preserve the source codec, bitrate, compression quality, tags, artwork, chapters, cue points, loop markers, or other container metadata. Audible artifacts from a lossy source can still remain in the decoded samples even though the source encoding itself is not carried into the WAV. Floating-point samples are quantized to signed 16-bit PCM during export.
What to do when a file is blocked
- If the encoded file exceeds 50 MiB: select a shorter or smaller encoded copy before starting. The effect tool cannot bypass the input-size ceiling.
- If the browser cannot decode the file: choose a source with a codec and profile supported by the current browser and operating system. An accepted extension is not proof that decoding will succeed.
- If the decoded input is too large: use a shorter source, or a version with fewer channels or a lower sample rate. Any such change affects the source, so preserve the original for comparison.
- If an echo or reverb tail pushes the output over budget: shorten the input and run the effect again. The tool does not create a partial or truncated result to force the file under the limit.
- If you need more than one effect: complete and download one effect at a time. Use the resulting WAV as the next input while retaining the earlier source and intermediate files.
Quality is separate from the size check
A 50 MiB ceiling describes input capacity, not fidelity or perceived quality. File size can reflect duration, channel count, sample rate, or encoding choices, so a larger file is not automatically better. Being under the ceiling also does not prove that the source is decodable, that its decoded data fits, or that an effect tail will leave enough room in the output budget.
The practical success checks are the completed local run, the reported channel and frame counts, the output peak, and the exact WAV byte size. Strong echo or reverb settings can clip when dry and delayed samples overlap; finite output samples are constrained to the legal −1 through +1 range before WAV quantization. Keeping the original file provides the reliable comparison because the download is a newly encoded PCM16 rendering rather than an untouched copy of the source.
For a deeper look, see What Should I Compare Before Using Audio Effects Online?.
For a deeper look, see What Does the Download Preserve From My Original File?.